lv series specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr (1) leakage current ( 2) performance characteristics item 55 to +105? 16 to 100v 6.8 to 470 f 20% at 120hz, 20? less than or equal to the specified value at 120hz, 20? less than or equal to the specified value at 100khz, 20? less than or equal to the specified value. after 2 minutes' application of rated voltage at 20? z+105? / z+20? 1.25 (100khz) z 55? / z+20? 1.25 endurance damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20? after the rated voltage is applied for 3000 hours at 105?. the specifications listed at right shall be met when the capacitors are restored to 20? after the rated voltage is applied for 1000 hours at 60?, 90% rh. after soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200? for 60 to 180 seconds and peak temperature at 265? for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. navy blue print on the case top capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3 ) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3 ) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 10% of the initial capacitance value ( 3 ) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value high voltage (to 100v), low esr, high ripple current. long life of 3000 hours at 105?. radial lead type: lead free flow soldering condition correspondence. compliant to the rohs directive (2002/95/ec). 1 esr should be measured at both of the terminal ends closest to the capacitor body. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage con tinuously to the capacitor for 120 minutes at 105?. 3 initial value : the value before test of examination of resistance to soldering. p 1 l 2 v 3 1 4 v 5 8 6 2 7 0 8 m 91011 capacitance tolerance ( 20%) rated capacitance (82 f ) rated voltage (35v) d l 12 1 size code series name type configuration l +0.5max. 15min 4min d +0.5 max. resin coated case tinned lead wire d lv 82 v 012 capacitance series lot. no. voltage(v:35v) p ? 0.5 dimensions type numbering system (example : 35v 82 f) radial lead type, long life assurance dimension table in next page. voltage v 16202535506380100 code c d e v h j k 2a size d l p d 10 13l 10.0 12.5 5.0 0.6 8 9l 8.0 8.5 3.5 0.6 8 12l 8.0 11.5 3.5 0.6 (mm) conductive polymer aluminum solid electrolytic capacitors lv lf high voltage long life please refer to page 20 about the end seal configulation. high temperature lx cat.8100a-1
conductive polymer aluminum solid electrolytic capacitors lv series rated ripple current (marms) at 105 c 100khz standard ratings rated voltage (v) code surge voltage (v) leakage current ( a) esr (m ? ) (at 100khz 20 c) rated ripple (marms) 2100 2500 2900 2000 2400 2800 2000 2400 2800 1900 2300 2700 1900 2200 2600 1800 2100 2600 1700 1900 2300 1600 1800 2200 26 24 23 27 25 24 28 26 25 29 27 26 32 29 28 35 33 29 40 38 35 45 42 38 704 864 1504 600 880 1320 600 750 1350 392 574 1050 330 390 680 277 340 592 160 192 352 136 200 360 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 8 9 8 12 10 13 220 270 470 150 220 330 120 150 270 56 82 150 33 39 68 22 27 47 10 12 22 10 18 18.4 23.0 28.7 40.2 57.5 72.4 92 115 16 (1c) 20 (1d) 25 (1e) 35 (1v) 50 (1h) 63 (1j) 80 (1k) 100 (2a) plv1c221mcl1 plv1c271mdl1 plv1c471mdl1 plv1d151mcl1 plv1d221mdl1 plv1d331mdl1 plv1e121mcl1 plv1e151mdl1 plv1e271mdl1 plv1v560mcl1 plv1v820mdl1 plv1v151mdl1 plv1h330mcl1 plv1h390mdl1 plv1h680mdl1 plv1j220mcl1 PLV1J270MDL1 plv1j470mdl1 plv1k100mcl1 plv1k120mdl1 plv1k220mdl1 plv2a6r8mcl1 plv2a100mdl1 plv2a180mdl1 rated capacitance ( f) case size d l (mm) tan part number 6.8 taping specifications are given in page 20, 21, 22. please refer to page 3 for the minimum order quantity. cat.8100a-1
|
